2N7000 N-channel MOSFET pinout

The onsemi 2N7000 is an enhancement-mode MOSFET for small low-side switching loads. Check the gate voltage against a specified on-resistance test point.

TO-92 straight leads

3 contacts Current package

TO-92 formed leads 3 contacts

onsemi · Case 135AN · 1.27 mm lead pitch · mechanical outline 98AON13880G.

Bulk bag code in 2N7000TA/D.

TO-92 straight leads pinout

TO-92 straight leads

Flat marked face toward you and leads pointing down. Left to right: source, gate, drain.

Selected pin details

1 · S

Source · Ground

Return reference for the gate drive in a low-side circuit. The intrinsic body diode has its anode here.

onsemi NDS7002A/D Rev. 11, p. 1

Electrical limits · Link to this pin

All 3 pins

Pin	Signal	Direction	Function
1	S Source	Source	Return reference for the gate drive in a low-side circuit. The intrinsic body diode has its anode here.
2	G Gate	Gate	Insulated gate. Establish a defined voltage relative to S. Use a gate-to-source pull-down if the driver can float.
3	D Drain	Drain	Connect to the low side of the load in a low-side switch. The intrinsic body diode has its cathode here.

Signal assignments

Low-side switch

Drive G relative to S. A pull-down holds the gate near S when the drive is disconnected. Put a resistive load between its positive supply and D.

Intrinsic diode

The diode conducts from S toward D if D falls sufficiently below S. Swapping source and drain can leave the load conducting when the gate is low.

Electrical limits

Parameter	Limit	Conditions and source
Continuous gate–source limit±30 V	±30 V	Absolute maximum VGS. onsemi 2N7000TA/D Rev. 1, p. 1
Gate threshold at 1 mA0.4–3.0 V	0.4–3.0 V	VDS = VGS, 25 °C. Use a specified on-resistance point to size the gate drive. onsemi 2N7000TA/D Rev. 1, p. 2
On-resistance at 4.5 V driveUnspecified	Unspecified	Use the 10 V gate-drive test point for this order code. onsemi 2N7000TA/D Rev. 1, p. 2
Drain–source voltage limit60 V	60 V	Absolute maximum for the listed onsemi parts. Check transient voltage and the safe operating area separately. onsemi NDS7002A/D Rev. 11 and onsemi 2N7000TA/D Rev. 1, p. 1
On-resistance at 10 V drive5 Ω maximum	5 Ω maximum	At ID = 500 mA under the specified electrical test conditions. The test current is separate from the 200 mA continuous maximum in the ratings. onsemi NDS7002A/D Rev. 11, pp. 2–3; onsemi 2N7000TA/D Rev. 1, pp. 1–2

Models and documents

onsemi TO-92 cases 135AN and 135AR. The 2N7000BU and 2N7000TA order codes use a separate electrical table. The SOT-23 2N7002 and NDS7002A have a different lead map and their own ratings.

2N7000: Bulk order code in NDS7002A/D.
2N7000BU: Bulk bag code in 2N7000TA/D.

onsemi 2N7000 datasheet· NDS7002A/D · Rev. 11 · March 2025 · 2N7000 electrical column, ordering and both TO-92 outlines.
onsemi 2N7000BU / 2N7000TA datasheet· 2N7000TA/D · Rev. 1 · July 2023 · Variant-specific ratings and ordering.
Source register· Manufacturer URLs, applicability and file checksums.