Motorola MC6809E pinout

Externally clocked Motorola 6809-family HMOS 8-bit MPU with 16 address lines, 8 data lines and separate bus control outputs.

MC6809 DIP-40 40 contacts

MC6809E DIP-40

40 contacts Current package

Motorola · Motorola P plastic (Case 711), S CERDIP (Case 734) and L ceramic (Case 715) share this top-view 40-pin assignment. External E and Q clocks.

1.0 MHz maximum bus rate. MC6809EP/S/L (0–70 °C) and MC6809ECP/CS/CL (−40 to +85 °C).

MC6809E DIP-40 pinout

Top view · Pin 1 at upper left · Schematic outline

Selected pin details

21 · A13

Output · Outputs

Address bit 13. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.

Motorola MC6809E datasheet DS9846-R2, pin assignment and pin descriptions

Electrical limits · Link to this pin

All 40 pins

Pin	Signal	Direction	Function
1	VSS Supply return	Supply return	Reference and supply return. Connect to the 0 V rail.
2	/NMI Input	Input	Falling-edge nonmaskable request. Inhibited after reset until software initializes the hardware stack pointer.
3	/IRQ Input	Input	Active-low level-sensitive interrupt controlled by the I flag. IRQ stacks the full processor state.
4	/FIRQ Input	Input	Active-low level-sensitive fast interrupt controlled by the F flag. FIRQ stacks the program counter and condition codes.
5	BS Output	Output	Bus status. Interpret with BA to distinguish normal execution, interrupt acknowledge, SYNC acknowledge and halt/bus grant.
6	BA Output	Output	Bus available. Interpret with BS and the timing table before granting another driver access to the bus.
7	VCC Supply	Supply	Regulated 5 V supply. Decouple to VSS close to the package.
8	A0 Output	Output	Address bit 0. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
9	A1 Output	Output	Address bit 1. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
10	A2 Output	Output	Address bit 2. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
11	A3 Output	Output	Address bit 3. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
12	A4 Output	Output	Address bit 4. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
13	A5 Output	Output	Address bit 5. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
14	A6 Output	Output	Address bit 6. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
15	A7 Output	Output	Address bit 7. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
16	A8 Output	Output	Address bit 8. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
17	A9 Output	Output	Address bit 9. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
18	A10 Output	Output	Address bit 10. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
19	A11 Output	Output	Address bit 11. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
20	A12 Output	Output	Address bit 12. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
21	A13 Output	Output	Address bit 13. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
22	A14 Output	Output	Address bit 14. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
23	A15 Output	Output	Address bit 15. Valid after the falling edge of E within the specified tAD delay. This line is three-state capable.
24	D7 Bidirectional	Bidirectional	Data bit 7. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
25	D6 Bidirectional	Bidirectional	Data bit 6. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
26	D5 Bidirectional	Bidirectional	Data bit 5. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
27	D4 Bidirectional	Bidirectional	Data bit 4. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
28	D3 Bidirectional	Bidirectional	Data bit 3. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
29	D2 Bidirectional	Bidirectional	Data bit 2. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
30	D1 Bidirectional	Bidirectional	Data bit 1. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
31	D0 Bidirectional	Bidirectional	Data bit 0. Driven by external memory on reads and the MPU on writes. Meet the setup and hold times around E.
32	R/W Output	Output	High for read and low for write. Qualify memory strobes with the clock and bus control for the exact CPU variant.
33	BUSY Output	Output	High during indivisible portions of certain read/modify/write, double-byte and vector operations. Use the timing diagram for multiprocessor arbitration.
34	E Input	Input	Externally driven bus timing input. E requires a near-rail high and its falling edge latches read data.
35	Q Input	Input	Externally driven quadrature timing input. Q must lead E. Check both phase spacings and input levels at the pins.
36	AVMA Output	Output	Advance valid memory address. Indicates that the next cycle will use the bus.
37	/RESET Input	Input	Active-low Schmitt-trigger reset. Needs at least 4.0 V to release. The CPU reads the reset entry point high byte at 0xFFFE, then low byte at 0xFFFF.
38	LIC Output	Output	Last instruction cycle. In normal execution, the high-to-low transition indicates the next opcode will be latched at the end of the present cycle.
39	TSC Input	Input	High puts the address, data and R/W buffers in high impedance according to E/Q timing. The status outputs remain driven.
40	/HALT Input	Input	Low pauses after the current instruction. BA and BS go high and the CPU releases the bus. Keep both clocks running.

Signal assignments

External memory bus

Use address, data, R/W and externally driven E/Q. AVMA anticipates the next valid memory access.

External quadrature clocks

Supply two synchronized phases with Q leading E. Verify E and Q against their different DC input limits.

Interrupts and reset

IRQ and FIRQ are level-sensitive and maskable. NMI is edge-sensitive and enabled after stack initialization. RESET has its own input threshold.

Bus ownership and instruction status

TSC releases the three-state bus drivers under E/Q timing. BA and BS report bus state, while BUSY and LIC expose instruction-cycle status.

Electrical limits

Parameter	Limit	Conditions and source
Operating supply4.75–5.25 V	4.75–5.25 V	VCC relative to VSS. Motorola MC6809E datasheet DS9846-R2, DC characteristics
RESET levelsLOW ≤ 0.8 V, HIGH ≥ 4.0 V	LOW ≤ 0.8 V, HIGH ≥ 4.0 V	Active-low Schmitt-trigger input. Check the driver high against the RESET threshold at the CPU. Motorola MC6809E datasheet DS9846-R2, DC characteristics
Logic inputsLOW ≤ 0.8 V, HIGH ≥ 2.0 V	LOW ≤ 0.8 V, HIGH ≥ 2.0 V	General logic inputs. E, Q and RESET have separate rows. Motorola MC6809E datasheet DS9846-R2, DC characteristics
E and Q inputsE: LOW ≤ 0.4 V, HIGH ≥ VCC − 0.75 V. Q: LOW ≤ 0.6 V, HIGH ≥ 2.0 V.	E: LOW ≤ 0.4 V, HIGH ≥ VCC − 0.75 V. Q: LOW ≤ 0.6 V, HIGH ≥ 2.0 V.	E can present 50 pF input capacitance and Q can present 15 pF. Verify the driver at each pin. Motorola MC6809E datasheet DS9846-R2, DC characteristics
Logic output levelsLOW ≤ 0.5 V at 2 mA, HIGH ≥ 2.4 V	LOW ≤ 0.5 V at 2 mA, HIGH ≥ 2.4 V	At minimum VCC. HIGH sourcing loads are 205 µA for data, 145 µA for address/R/W and 100 µA for BA/BS/LIC/AVMA/BUSY. Motorola MC6809E datasheet DS9846-R2, DC characteristics
E and Q rate100 kHz minimum, 1 / 1.5 / 2 MHz maximum	100 kHz minimum, 1 / 1.5 / 2 MHz maximum	Maximum by grade. E and Q use the same cycle frequency and four specified edge separations. Motorola MC6809E datasheet DS9846-R2, bus timing table
Absolute voltage limits−0.3 to +7.0 V	−0.3 to +7.0 V	VCC and input stress limits relative to VSS. Use the operating values for circuit design. Motorola MC6809E datasheet DS9846-R2, maximum ratings

Models and documents

Covers the Motorola MC6809 and MC6809E plus their A and B speed grades. On the MC6809, E and Q are outputs. On the MC6809E, both are inputs, and pins 33, 36, 38 and 39 also differ. Hitachi HD6309 and later CMOS versions require their own datasheets.

MC6809E: 1.0 MHz maximum bus rate. MC6809EP/S/L (0–70 °C) and MC6809ECP/CS/CL (−40 to +85 °C).
MC68A09E: 1.5 MHz maximum bus rate. MC68A09EP/S/L (0–70 °C) and MC68A09ECP/CS/CL (−40 to +85 °C).
MC68B09E: 2.0 MHz maximum bus rate. MC68B09EP/S/L (0–70 °C) and MC68B09ECP/CS/CL (−40 to +85 °C).

Motorola MC6809 datasheet DS9845-R2· Manufacturer scan, © 1983. Pin map p. 1, electrical and bus timing pp. 2–3, crystal and reset pp. 7–8, ordering p. 35. Scan SHA-256 87037123596de83bbc44ac63fbcde3950d368d5ee30880bffaa54e23bb81ea68.
Motorola MC6809E datasheet DS9846-R2· Manufacturer scan, © 1984. Check the pin assignment, external clock thresholds and timing, TSC timing and ordering table. Scan SHA-256 42c50598f2184bc37535a8d59be60a895c14e34919d706317b18f02f73441808.
Motorola MC6809–MC6809E Microprocessor Programming Manual· Programming model, interrupt handling and vectors. Appendix B lists the two pin assignments side by side.