74HC245 connection guide
Set up a one-bit test and use a high-impedance interval to hand the bus to the other driver.
Power the IC with its outputs disabled
With power off, wire a regulated 4.5 V rail to pin 20 VCC and the common return to pin 10 GND. Place one 100 nF ceramic capacitor (16 V or higher) close to the IC across those pins. Share the return with the controller and both endpoints. Use rail-compatible controls and endpoints on this same supply.
Soldering the exposed pad is optional. If soldered, leave its land electrically floating or connect it to GND. Always connect pin 10 to ground.
Pull /OE (pin 19) up to VCC with 10 kΩ so it defaults HIGH while the powered controller output is high impedance. Use a push-pull control with fast edges for switching. The pull-up adds about 0.45 mA at LOW on this rail. Hold DIR at a defined level through startup, using a 10 kΩ pull-down if the DIR controller starts in high impedance. Keep external signals within the rails, including during power sequencing.
EP is the exposed center pad on the underside.
Wire and bias the data pins
Connect endpoint A to A0 (pin 2) and endpoint B to B0 (pin 18). Use endpoints that can switch between driving and a high-impedance input. The controller or bus protocol must coordinate both endpoint drivers and the 74HC245 controls. Connect the controller outputs to DIR (pin 1) and /OE (pin 19). Power up with both endpoints in receive mode and /OE HIGH.
Fit one 10 kΩ pull-down per data pin, A0–A7 (2–9) and B0–B7 (11–18), including the two connected to the endpoints. Each resistor loads a HIGH by about 0.45 mA at 4.5 V. The resistors define LOW when the drivers release, including during handoff. Sample only during a valid transfer and verify total loading and leakage with the endpoints attached.
Test the signal path
A → B
Start with /OE HIGH. Configure B as an input, set DIR HIGH and establish valid data at A0. Then drive /OE LOW.
/OE LOW · DIR HIGH
| State | Endpoint A | Endpoint B |
|---|---|---|
| A → B | Drive | Receive |
Read the arrow from A0 (2) to B0 (18). Drive 0 V and then 4.5 V at the source. With total output load ≤ 6 mA, including the pull-down and endpoint, expect ≤ 0.40 V and then ≥ 3.70 V, respectively. Measure relative to pin 10 with a high-impedance meter.
EP is the exposed center pad on the underside.
Arrows show signal direction between paired pins.
The map highlights the test bit and its controls. DIR and /OE apply to all eight bits.
Complete A → B to B → A handoff
| Phase | /OE | DIR | End A | End B |
|---|---|---|---|---|
| A drives | LOW | HIGH | Drive | Receive |
| Release both | HIGH | HIGH | Receive | Receive |
| Change DIR | HIGH | LOW | Receive | Receive |
| Prepare B | HIGH | LOW | Receive | Drive |
| B drives | LOW | LOW | Receive | Drive |
- Begin with endpoint A driving valid data and endpoint B configured as an input.
- Drive /OE HIGH and wait for the 74HC245 output to release. Then put endpoint A in receive mode and wait for its output to release. Endpoint B stays in receive mode.
- With both endpoint drivers off and /OE still HIGH, drive DIR LOW and let it settle at the IC pin.
- Keep /OE HIGH and endpoint A in receive mode. Enable endpoint B’s driver and wait for valid data at B0.
- Pull /OE LOW only after B0 is valid and A is receiving. Allow enable and data settling time before sampling A0. Swap the port roles for the return handoff.
At 4.5 V, 50 pF and −40 to +125 °C, the 74HC245 output enable and disable delays are each 45 ns maximum under the datasheet test conditions. Budget from the control signal reaching the pin. Include worst-case release and enable times of the external endpoints, board loading, DIR and data settling, and margin. Confirm the timing and direction at the pins with a scope before using the sequence at speed.
Source for logic and timing: datasheet §6 Table 3, §9 Table 6 and §10 Table 7 and Fig. 4.
Package and documents
74HC245BZ · Nexperia SOT8020-1 · 3.2 × 2 mm body · 0.4 mm terminal pitch. Production order code 74HC245BZX.
Scope: Nexperia’s commercial 74HC245 packages in Rev. 9. The legacy N (PDIP20) and DB (SSOP20) were removed in earlier revisions. The shared datasheet also describes 74HCT245, which has different input thresholds and operating supply limits. The automotive 74HC245-Q100 series has its own datasheet.
- Nexperia 74HC245 datasheet (PDF)· 74HC_HCT245 Rev. 9 · 9 May 2025
- SOT8020-1 package drawing (PDF)
- 74HC245BZ product and order codes
- Nexperia series and ordering status
Pin assignments and exposed pad: §5, p. 3. Package versions: §3 Table 1. Use the standalone SOT8020-1 drawing for the DHXQFN20 footprint. Fig. 9 in Rev. 9 repeats the DHVQFN20 outline.