HX8367 TFT LCD controller pinout · Winstar WF0283ATDAJDNN0 · 47-contact FPC

Winstar WF0283ATDAJDNN0 · 47-contact FPC pinout

Winstar WF0283ATDAJDNN0 · 47-contact FPC

Match contact 1 to the module outline drawing. The flex contact pitch is 0.8 mm.

Selected pin details

22 · DB5

Bidirectional · Data

Display data bus bit 5.

Winstar WF0283ATDAJDNN0, pp. 2–5, operating conditions and LCM pin definition.

Electrical limits · Link to this pin

All 47 pins

Pin	Signal	Direction	Function
1	IM0 Input	Input	Interface mode strap. Check the module’s mode table.
2	IM1 Input	Input	Interface mode strap. Check the module’s mode table.
3	IM2 Input	Input	Interface mode strap. Check the module’s mode table.
4	IM3 Input	Input	Interface mode strap. Check the module’s mode table.
5	RESET Input	Input	Active-low reset after power-up.
6	VSYNC Input	Input	RGB frame sync.
7	HSYNC Input	Input	RGB line sync.
8	DOTCLK Input	Input	RGB pixel clock.
9	ENABLE Input	Input	RGB data enable.
10	DB17 Bidirectional	Bidirectional	Display data bus bit 17.
11	DB16 Bidirectional	Bidirectional	Display data bus bit 16.
12	DB15 Bidirectional	Bidirectional	Display data bus bit 15.
13	DB14 Bidirectional	Bidirectional	Display data bus bit 14.
14	DB13 Bidirectional	Bidirectional	Display data bus bit 13.
15	DB12 Bidirectional	Bidirectional	Display data bus bit 12.
16	DB11 Bidirectional	Bidirectional	Display data bus bit 11.
17	DB10 Bidirectional	Bidirectional	Display data bus bit 10.
18	DB9 Bidirectional	Bidirectional	Display data bus bit 9.
19	DB8 Bidirectional	Bidirectional	Display data bus bit 8.
20	DB7 Bidirectional	Bidirectional	Display data bus bit 7.
21	DB6 Bidirectional	Bidirectional	Display data bus bit 6.
22	DB5 Bidirectional	Bidirectional	Display data bus bit 5.
23	DB4 Bidirectional	Bidirectional	Display data bus bit 4.
24	DB3 Bidirectional	Bidirectional	Display data bus bit 3.
25	DB2 Bidirectional	Bidirectional	Display data bus bit 2.
26	DB1 Bidirectional	Bidirectional	Display data bus bit 1.
27	DB0 Bidirectional	Bidirectional	Display data bus bit 0.
28	SDO Output	Output	Serial data output.
29	SDI Input	Input	Serial data input.
30	RD Input	Input	Parallel read strobe.
31	WR/SCL Input	Input	Parallel write strobe or serial clock.
32	RS Input	Input	Register or data selection.
33	CS Input	Input	Active-low chip select.
34	FMARK Output	Output	Frame-mark output for host synchronization.
35	IOVCC Supply input	Supply input	Digital I/O supply.
36	VCC Supply input	Supply input	Supply contact labelled VCC in the flex table.
37	VCI Supply input	Supply input	Supply contact labelled VCI in the flex table.
38	GND Supply return	Supply return	Connect to host ground.
39	NC None	None	Reserved contact. Leave open.
40	NC None	None	Reserved contact. Leave open.
41	NC None	None	Reserved contact. Leave open.
42	NC None	None	Reserved contact. Leave open.
43	LEDA Supply input	Supply input	Backlight LED anode.
44	LEDK1 Backlight return	Backlight return	Backlight LED cathode. Connect to a current-regulated return.
45	LEDK2 Backlight return	Backlight return	Backlight LED cathode. Connect to a current-regulated return.
46	LEDK3 Backlight return	Backlight return	Backlight LED cathode. Connect to a current-regulated return.
47	NC None	None	Reserved contact. Leave open.

Signal assignments

Parallel MPU interface

Use the mode straps and bus width of the fitted controller.

Serial interface

WR/SCL becomes the clock in serial mode.

RGB timing signals

The host generates the pixel clock, data-enable and sync signals.

Electrical limits

Parameter	Limit	Conditions and source
VCI2.5–3.3 V, 2.8 V typical	2.5–3.3 V, 2.8 V typical	Winstar operating conditions. Winstar WF0283ATDAJDNN0, pp. 2–5, operating conditions and LCM pin definition.
IOVCC1.65–3.3 V, 1.8 V typical	1.65–3.3 V, 1.8 V typical	Host signaling is referenced to IOVCC. Winstar WF0283ATDAJDNN0, pp. 2–5, operating conditions and LCM pin definition.
Panel pixels240 × 320	240 × 320	Use initialization for the actual fitted controller. Winstar WF0283ATDAJDNN0, pp. 2–5, operating conditions and LCM pin definition.

Models and documents

The map covers the 47-contact WF0283ATDAJDNN0 described by Winstar. The manufacturer lists HX8367-A or an equivalent driver, so check which controller is fitted before selecting initialization.

Winstar WF0283ATDAJDNN0: 240 × 320 transflective panel, 47 contacts.

Winstar WF0283ATDAJDNN0 (HX8367-A) manufacturer documentation· Winstar WF0283ATDAJDNN0, pp. 2–5, operating conditions and LCM pin definition.